Micronutrient fertilizer LURS^® colofermin zinc

LURS^® colofermin zinc is a concentrated micronutrient fertilizer for foliar feeding of field, vegetable and perennial crops.

*Colofermine is a multicomponent complexing agent (analogue of chelating agents), which consists of various organic compounds, optimally balanced for maximum absorption and plant uptake (up to 100%) of the corresponding nutrients (main active ingredient) in micronutrient fertilizers.

Depending on the type of micronutrient fertilizers, among other components, colofermin may contain colamine, various complexes of amino acids, micronutrients, including nitrogen, sulfur, sodium in sufficiently high concentrations (up to 280 g/L). Therefore, colofermin also serves as an additional source of plant nutrition.

Due to the above-mentioned factors, our formulations are more effective than the ones, produced by our competitors, even if they have a little higher concentration of an active ingredient.

LURS^® colofermin zinc eliminates effectively zinc deficiency in plants. It does not contain any ballast additives, so it does not cause leaf burn. It is completely absorbed through the leaf surface of plants.

Zinc influences the process of auxin synthesis, which controls plant growth.

When nutrition with zinc is enough, and sharp change in air temperature takes place, plant respiration is less susceptible to extremes. This is one of the reasons for heat resistance and hardiness.

The presence of zinc is a prerequisite for carbohydrate synthesis in cells. With the shortage of zinc, the starch content in seeds decreases.

Crops that are in special need of zinc are as follows: corn, flax, grapes, orchards, legumes, sugar beet, sunflower, onions, potatoes, cabbage and cucumbers.

Symptoms of zinc deficiency develop throughout the plant or they are localized in the old lower leaves. First just lower and middle leaves, and then all the plant leaves are covered with gray-brown and magenta spots. Tissues of these areas die. Young leaves are abnormally small and covered with yellow spots, take slightly upright position. The root system is poorly developed. The stems are thin.

When applying LURS^® colofermin zinc there is a reduction in fungal diseases affection, sugar content of fruit and berry crops increases. Drought, cold and heat resistance of plants increase.

The formulation contains a high concentration of zinc ions, which provides a reduction in rate of application and hence expenses per hectare. The formulation is very rapidly absorbed by leaves and eliminates diseases caused by zinc deficiency.

Composition of zinc and sulfur, which is a part of the formulation, intensifies growth of the vegetative mass and inhibits fungal diseases. Nitrogen in LURS® colofermin zinc is in the form of amide and ammonia, which enhance root development.

LURS^® colofermin zinc can be used in any water. There is no danger of the calcium sulphate (gypsum) formation.

Compatibility: LURS^® colofermin zinc performs well in tank mixes with herbicides, insecticides, fungicides and biological preparations. Prior to starting preparation of a tank mix, always check the formulations for compatibility.

To avoid leaf and fruit burn, do not apply the formulations in high air temperatures. To obtain the maximum effect, it is advisable to conduct treatments in the evening.

Treatment during the flowering period is not recommended.

LURS^® colofermin zinc has a significant physiological effect on plants, namely:

It is recommended for use in conjunction with VIMPEL ^®plant growth stimulator.

1. INFORMATION FOR CONSUMERS: follow the instructions when using the formulation. The efficacy of the formulation and its ease of use depend on the application, storage and transportation conditions specified by the manufacturer.

2. COMPATIBILITY WITH OTHER FORMULATIONS: the micronutrient fertilizer is applied during the growing season either prophylactically or according to the diagnostics results based on the application regulations. It performs well in tank mixes with plant protection products (unless otherwise specified by the manufacturer of the plant protection products), urea (in the recommended concentrations when using foliar fertilization of agricultural crops according to the crop growth stages), UAN, plant growth regulators, microfertilizers and biological preparations.

3. PREPARATION OF WORKING TANK SOLUTION:

Warning! Prior to starting preparation of a tank mix, always check the formulations for compatibility!

For this purpose take a container, pour in it some water (which is to be used for the main application), add the tank mix components in proportions, based on the field rates of consumption. After closing the container, mix the contents by shaking it 10-15 times. Evaluate the tank mixture visually twice: immediately after mixing and after the mixture has settled (in about 30 minutes). Incompatibility of formulations is indicated by their separation into layers, residuum occurrence, flocculation of the mixture, formation of sludge that does not disperse.

Attention! It is possible to use the formulation in hard water due to the water softener in its composition. At the same time, if there is high concentration of hardness salts and significant amount of water, it is possible that after some time there will be a slight separation of hardness salts in the form of gypsum (СаSO₄٠2H₂O). In this case, the amount of sulfur in the solution is slightly reduced. These processes in no way affect the solution usability or cause the possibility of spraying equipment failure, as the formulation is finely dispersed. When forming a tank mixture in hard water, we recommend spraying with the mixing mode turned on. After application of the tank mix, it is necessary to rinse the tank with water to prevent the overgrowth of gypsum crystals.

If there are no compatibility problems, prepare the working solution just before spraying (direct application). Shake the product thoroughly in the original package and pour it directly into the sprayer tank, which is to be previously filled with water to 2/3 of its volume. After this with the mixing mode turned on add the components of the tank mixture in sequence stated in the recommendations and finish the process with filling the tank with water. Stirring of the mixture should be continued throughout the period of its preparation, as well as during application.

Application rates of the spraying solution: field crops — 70-300 L/ha, vegetables — 300-400 L/ha, fruit crops and grapes — 800-1000 L/ha.

4. MIXING ORDER OF SPRAYING SOLUTION COMPONENTS: when preparing the tank mixture, stick to the following sequence of components.

Tank mix

Attention! In preparing a tank mix, care should be taken to ensure that the mixing of the components (such as growth regulators, PPPs, microfertilizers, etc.) is conducted solely in water!

5. APPLICATION REQUIREMENTS: spraying should be done either early in the morning or in the evening, when the humidity level is high to avoid chemical leaf burn. The optimum air temperature is +10…+25 °С (50 — 77 ºF), wind speed up to 5 — 7 m/s depending on the sprayer type. It is not recommended carrying out spraying operations during foggy weather or in the presence of dew, which can lead to surface overflow of the solution and hence the reduction of the treatment efficiency. The spraying should be stopped 1.5 — 2 hours before the rain.

Attention! Use а freshly mixed solution. Do not store the prepared solution more than 24 hours.

6. STORAGE AND TRANSPORTATION: The formulation should be stored in a warehouse or storage building, designed specifically for this purpose. Storage area should be free of direct sunlight, moisture, pollution and mechanical damage to the container. Store at temperature above 0 ºС below +30 ºС (50 — 86 ºF), in the original closed package in an upright position, with the cap facing up in a cardboard box. Do not stack cardboard boxes more than 3 high.

Decrease of temperature below -25 ºС (-13 ºF) results in the product decrease of viscosity, the prolonged storage may cause sediment formation.

Any form of transport is possible while in covered vehicles. The use of open vehicles, which provide protection against precipitation, is allowed as well.

7. WHO CLASSIFICATION, TOXICITY: 4^th toxicity class. The formulation is nontoxic, does not cause allergies, is environmentally friendly and absolutely harmless to pollinating insects.

8. PRECAUTIONS: keep away from children and animals. When carrying out spraying operations, use the appropriate and adjusted equipment, follow generally accepted safety standards.

9. FIRST AID INSTRUCTIONS: if the skin or eyes are contaminated with the preparation, flush them with water. If necessary, call a doctor.

10. CONTAINER AND LEFTOVER FORMULATION DISPOSAL: a container and leftover formulation do not require specific methods of disposal and neutralization.

11. STORAGE PERIOD: 5 years.